About this list Date view Thread view Subject view Author view Attachment view

From: Jean-Marc Pigeon (jmp_at_safe.ca)
Date: Sun 30 Jan 2005 - 01:15:20 GMT


Bonjour Herbert Poetzl,

        I was successful to compile 2.6.11-rc2-vs1.9.4-rc3-ng8.12,
        it is almost working as (I) expected...
        reliability is a little bit shaky (but this could
        be related to me not fully mastering the 'beast').

        I defined a vserver with an 'lo' and 'eth0',
        'eth0' is set with a public IP number such I expect
        to reach Internet from vserver.

        vserver 'lo' interface is defined, is not mixed up
        with mserver 'lo' interface (test show 127.0.0.2
        on mserver IS NOT 127.0.0.2 on vserver... good).

        once defined vserver 'eth0' is pingable FROM
        mserver, but NOT from another system on the same
        network...
        mserver 'eth0' is NOT pingable from vserver
        (Network is unreachable).

        If I manually set route such as:
        /sbin/route -v add -net IP.PUBLIC.NETWORK.0/24 dev eth0
        then vserver is NOT pingable anymore from mserver (HOST unreachable)

        ping is almost working from the vserver side, tcpdump
        show packet reaching targeted system, but targeted system
        not being able to reply back, as if vserver ARP NOT providing
        needed information.

        Is my understanding correct?, once defined by 'vnet' and
        handle by iptables, such as...
(
vnet -x $XID -n ${XID}0 -d lo
vnet -x $XID -n ${XID}1 -d eth0 -D en0
iptables -t vnet -A PREROUTING -d $VIP -j VNET --vnet ${XID}1
iptables -t vnet -A OUTPUT -s $VIP -j VNET --vnet ${XID}1
)
        we should be able to run
        ->service network start<-
        on the vserver side, right??
        Here there is some complains I am getting from
        the vserver side:
(
Setting network parameters: error: unknown error 1 setting key 'net.ipv4.ip_forward'
error: unknown error 1 setting key 'net.ipv4.conf.default.rp_filter'
error: unknown error 1 setting key 'net.ipv4.conf.default.accept_source_route'
error: unknown error 1 setting key 'kernel.sysrq'
error: unknown error 1 setting key 'kernel.core_uses_pid'
)
        Obviously ifup and Co need to be adjusted...
        
        Does somebody can give me a hint about, how to make
        vserver 'eth0' getting ping reply from the rest of the world???

        Could somebody confirm he was successful with such test?

        Thank for your time and 'bravo!' for ng near to be working...
        
A bientot

--
==========================================================================
Jean-Marc Pigeon		      Internet:   Jean-Marc.Pigeon_at_safe.ca
SAFE Inc.		    	Phone: (514) 493-4280  Fax: (514) 493-1946
       REGULUS,  a real time accounting/billing package for ISP
           REGULUS' Home base <"http://www.regulus.safe.ca">
==========================================================================
_______________________________________________
Vserver mailing list
Vserver_at_list.linux-vserver.org
http://list.linux-vserver.org/mailman/listinfo/vserver


About this list Date view Thread view Subject view Author view Attachment view
[Next/Previous Months] [Main vserver Project Homepage] [Howto Subscribe/Unsubscribe] [Paul Sladen's vserver stuff]
Generated on Sun 30 Jan 2005 - 01:16:14 GMT by hypermail 2.1.3